View Single Post
Old 12-16-2007, 03:36 PM   #2 (permalink)
alantani
Member
 
Join Date: Feb 2007
Location: saratoga, ca
Posts: 72
now for the right side plate bearing.



our handy dandy bearing pulling tool will remove the bearing cover.



it will also remove the bearing (key #26).



this bearing was rusted as well. this new bearing is also a 0.125 x 0.5 x 0.172.



let's line everything up.



first, install the bridge screws (key #'s 16 and 17). note that the screws that are threaded just at the tip go on top.



your left index and middle finger cover the bridge screws. the right side plate (key #1) is held between your left thumb and ring finger.



now you can flip the side plate over with no risk of having the screws fall out.



install the clutch springs (key #18).



install the pinion yoke (key #12) and pinion gear (key #13) as a unit.



install the eccentric jack (key #11).



install the bridge/main gear assembly, turned 90 degrees counterclockwise from it's final position.



install the dog (key #15) and dog spring (key #14) as a unit. lay it down over the bridge screw and note that the dog spring sticks out too far.



press down on the bridge assembly with your left thumb. use the blade of a small flat screwdriver to push the dog spring down into it's final position.





rotate the bridge assembly 90 degrees clockwise and push it down into it's final position.



with a right hand assist, flip the right side plate assembly over.



start each bridge screw half way, then cinch down each screw until they are snug.



verify that the freespool lever (key #21) works properly.



verify that the secondary freespool lever (key #21C) functions properly. this lever allow the handle to turn backwards by disengaging the dog.



install the spacing sleeve (key #9).



install the star (key #10).



install the upgraded handle (key #24). add a light coat of grease.



install the handle screw (key #23).



install the handle lock screw (key #23A).



press the right side plate assembly down into the right side ring (key #2) until it seats, turn the right side plate assembly clockwise until the take apart thumb screw (key #41) lines up with the threaded screw hole, and turn the thumb screw down until it seats.



congratulations! you're done!



now, for a couple of comments. honestly, there is no way that this upgrade was anywhere near worth the time and expense that was required. but this was never about money, was it. i know one thing for sure. the new owner was a very proud and happy man. personally, i much prefer the balance that the narrowed frame offers. i like my reels "boxed out," having a spool that is as wide as it is tall. with greased carbon fiber drag washers, this reel will deliver a maximum of 12-15 pounds of drag at the top of the spool. the stock brass gear sleeve will start to round off at drag settings in excess of 8 pounds. the stainless steel gear sleeve will easily hold up under 15 pounds of drag. that means that this stainless steel gear sleeve is a worthwhile upgrade ONLY if you are going to fish a 10 pound drag setting with, say, straight 30# mono. that works out well, because the gap between the spool and side plate rings can be so large that the reel will eat 25 pound mono or less. it will also obviously eat spectra. this is an important point. this is not a spectra ready, or spectra worthy, reel.

maintenance of this reel is very simple. the screw holes and drag washers will be good forever. it would be a simple matter to strip off all the line, take the reel apart, flush it out with a full blast of water from a hose, blow out the bearings with compressed air, lube the bearings with more corrosion x, reassemble the reel, spool it up with more 30# mono, reset the drag and set it aside for the next fishing trip. if the bearings foul, you now know how to replace them. other than a fresh water rinse and blow dry, only the bearings are at risk for failure. if you are distance casting, you know that bearing maintenance is critical.
alantani is offline   Reply With Quote